Stock replacement and performance fuel pumps for Datsun 240Z, 260Z and 280Z. Electric fuel pump conversions for 240Z with fuel pump block off plates.
OEM Nissan fuel pump filter for Datsun 240Z and 260Z with factory electric fuel pump. This is the filter that is located in the pump at the rear of the car. Also fits Datsun...
OEM Nissan fuel pump filter for Datsun 240Z and 260Z with factory electric fuel pump. This is the filter that is located in the pump at the rear of the car. Also fits Datsun...
OEM Nissan fuel pump filter for Datsun 240Z and 260Z with factory electric fuel pump. This is the filter that is located in the pump at the rear of the car. Also fits Datsun...
Fuel pump fitting to adapt from -8 O-ring to 6AN flare (3/8 fuel line). This fitting will work with our high pressure fuel pump (Part# 800-436).
New genuine Nissan Nismo fuel pump. This is the same style of pump used on the Datsun 240Z, 1970-1973. Will work on any carburetor application. Great for stock SU's or Weber...
New electric fuel pump for use with carburetors. This fuel pump will work on any Datsun 240Z, 260Z and 280Z running stock or aftermarket carburetors. This pump can be run in...
New aluminum inline fuel gauge fitting. For 5/16" or 3/8" rubber fuel line and it has 1/8" NPT threads for adding a gauge.
New aluminum inline fuel gauge fitting. For 5/16" or 3/8" rubber fuel line and it has 1/8" NPT threads for adding a gauge.
Aluminum Fiberglass Heat Reflective Adhesive Tape, helps to shield fuel lines, brake lines, wire looms, and more from radiant heat--so it's great for quick "on the go" heat...
Aluminum Fiberglass Heat Reflective Adhesive Tape, helps to shield fuel lines, brake lines, wire looms, and more from radiant heat--so it's great for quick "on the go" heat...
New OEM genuine Nissan fuel pump spacer with gaskets for L series 4-cylinder engines found in Datsun 510 sedan and 610 trucks 1968-79. Will not fit 6-cyl "L" engines.
Fule pump gasket for Datsun 510 1968-1981. Four cylinder engine only.
TSP's high-flow, electric fuel pump is a great fuel delivery solution for your EFI power plant. Housed in the "044" style, it comes with all fittings and post hardware for...
New fuel pump install kit for electric fuel pumps. Use this kit for install of electric pumps for EFI and carbs. This kit allows for proper voltage to reach the pump so it...
New fuel pump install kit for electric fuel pumps. Use this kit for install of electric pumps for EFI and carbs. This kit allows for proper voltage to reach the pump so it...
AN flare connector with 1/8" NPT port for adding a guage or sensor. Available with -4AN, -6AN or -8AN male fittings.
4AN male to female fitting with 1/8 inch NPT port for a sensor. Choose from single or dual NPT Ports.
AN flare connector with 1/8" NPT port for adding a guage or sensor. Available with -4AN, -6AN or -8AN male fittings.
AN flare connector with 1/8" NPT port for adding a guage or sensor. Available with -4AN, -6AN or -8AN male fittings.
Fuel pump wire grommet for the floor board of 1977-78 Datsun 280Z. This grommet will install in the floor board/storage compartment area behind the passenger seat. Fits hole...
New phenolic plastic fuel pump insulator spacer for Datsun 240Z and 260Z cars with mechanical fuel pumps. This spacer has two functions, one is to get the correct spacing for...
New 240Z fuel sending/pump wiring harness grommet located in the right rear hatch area.
New 12V 40A relay for wiring accessories such as fuel pump, electric fan or any high current draw accessory. Includes relay and plug in harness.
New factory style electric fuel pump for Datsun 240Z and 260Z, 1970-74. This fuel pump is for cars with carburetors (not for fuel injection). Works great with stock SU type...